• Category Archives Studio G
  • Stamp Company » Studio G

  • Mosaic Tutorial

    Posted on by Julie 7 Comments

    Supplies Needed: (click on any image to enlarge)

    1. Sticker Paper
    2. Various Scraps
    3. Black Embossing Powder
    4. Brayer
    5. Heat Gun
    6. Black Marker (Galaxy Deep Space Black or Permopaque Black)
    Supplies Needed

    Step 1.
    Pick some scraps. I usually use 3 or 4 color groups. Here, I selected some blues, turquoise, and an orchid color for contrast. Scraps that are stamped and/or embossed will work well, too. With scissors, cut some of each color you plan to use. Vary the sizes and angles slightly. I try to leave 2 sides fairly square so they fit around the edges.

    Step 1.
    Step 1.

    Step 2:
    Cut your sticker paper to the size you want. For my example, my sticker sheet measures 3.25″ x 4.25″. I precut to this size because I want to leave a border around the edge of my sticker paper.
    I put a little removable adhesive on the back side of my sticker paper to hold it still while I am working with it. Peel the release sheet off the sticky side of your sticker paper. Start placing your cut mosaic pieces. I start in one corner and work across. Vary the pieces and colors.

    Step 2.

    Note that one piece is hanging over the border. When a piece does not fit correctly, use your scissors to trim it before pressing it down. (Step 2a)

    Step 2a
    Step 2a

    Step 3:
    Finish arranging your pieces. I find it easier to place my pieces on the sticker paper if I use a pair of needle nose pliers. Note the border around my pieces. You do not have to have this border.

    Step 4:
    Place the release paper over your mosaic. Using the brayer, roll over the release paper covered mosaic. This will help to secure the pieces to your sticker paper.

    Step 4
    Step 4

    Step 5:
    Coat your piece with the embossing powder. For my example, I am using detail black powder. Gently tap off excess. Place the release paper over the piece again and repeat the pressing with your brayer. This will help the embossing powder to cover the exposed areas of the sticker paper (“grout lines”).

    Step 5
    Step 5


    Step 6:
    Melt the embossing powder with your heat gun. Note that when using black embossing powder, tiny areas of the white may show through. This is not noticeable with other colors of embossing powder. If you look closely, you can see this, especially around the outer border.

    Step 6
    Step 6

    Step 7:
    Since I am using the black powder, I go over the “grout lines” with a permanent black marker. After testing a number of these, I found that the Galaxy or the Permopaque work the best and do not dull the shine of the embossing powder.

    Step 7
    Step 7
    Finished Mosaic Sheet
    Finished Mosaic Sheet
    Finished card using the mosaic example.
    Finished card using the mosaic example.

    Other Supplies used for this card:
    Spellbinders Nestabilities: Flower set, oval and scalloped oval sets
    Hole punches in 2 sizes
    Sentiment image: Studio G

    Julie2 sig


    This entry was posted in Embossing/Dry or Heat Mosaic/Faux Mosaic Spellbinders Nestabilities Studio G Tutorials and tagged

  • Sketchy Mosaic

    Posted on by Julie 1 Comment


    Wonderful sketch challenge today at SCS! I also did another mosaic to go w/ Monday’s TLC. Gotta love a technique that uses up scraps.

    I did my bg mosaic like Monday’s: w/ all kinds of scraps cut into pieces and attached to sticker paper. It’s coated w/ black embossing powder which sticks to the areas left open and becomes my “grout” when heated. I had some requests for a tutorial after I posted Monday’s mosaic, so I took pics along the way for this one and the tutorial should be up here on my blog by tomorrow.

    The flower is from a Nestabilities set. For my vertical band, I attached 3 narrow strips and staggered the lengths. I added faux brads made w/ 2 sizes of hole punches. All panels were edged w/ black to give a faux layer look.

    Supplies:
    Stamps: Studio G, various images on scraps
    Paper: DCWV mat stack (close = to orchid oppulence, taken w/ teal and cool caribbean, sticker paper, leftover scraps
    Ink: AP coal
    Accessories: black ep, black Permopaque marker, nestie flowers and ovals, hole punches

    Julie2 sig


    This entry was posted in Embossing/Dry or Heat Spellbinders Nestabilities Splitcoast Challenges Studio G

  • Reindeer & Christmas Trees

    Posted on by Julie 8 Comments

    It’s Inspiration Challenge day at SCS. And did I ever love the inspiration from Mizue Hirano. I chose the two in the third row down.

    Both were done on water color paper using a flat wash brush and a small detail brush. Instead of watercolors, I used dye reinkers because I like the vibrant color and transparency. I first made the abstract backgrounds then dried them with the heat gun because I’m too impatient to wait.

    Julie Warner - justwritedesigns https://thewritestuff.justwritedesigns.com/

    I made the white frames with the method I developed for resizing the Nestabilities rectangles. The tutorial for this is under my Tutorial heading. I edged the frames with a red marker. All the images were embossed using black pigment ink and black embossing powder. These cards measure 4.25″ x 5.50″. The greeting tag on Reindeer was cut out using a nestie circle.

    Julie Warner - justwritedesigns https://thewritestuff.justwritedesigns.com/

    Supplies:
    Stamps: Autumn Leaves, Inkadinkado, Studio G, Stampendous, Imaginisce
    Paper: white, water color, red
    Ink: black pigment & black embossing powder
    Accessories: paint brushes, dye reinkers, nestie rectangles & circles. red marker (to edge the frame & tag), black marker (to edge the Christmas Trees panel)

    Julie2 sig


    This entry was posted in Christmas/Holiday/Winter Embossing/Dry or Heat Imaginisce Inkadinkado Spellbinders Nestabilities Splitcoast Challenges Stampendous Studio G Watercolor and tagged