• Tag Archives Splitcoast
  • SCS Challenge

  • H is for Harvest

    This is my combo for yesterday’s sketch and today’s ways to use it challenges. I had a lot of fun w/ both of these.

    I stamped all the images (FireCracker Designs ) w/ either sienna ink or the Kpads (leaves only). I colored the pumpkins w/ markers and used a blender on the leaves. Then I outlined everything w/ a brown gel pen to give a little more definition. Everything was cut out.

    The green and marigold layers, I used cb border folders on. The vanilla rectangle behind the pumpkins I used the harvest folder. I used the nestie rectangles to get my long frame and the small sentiment frame. This was a little bit complicated until I figured out how to make my standard rectangle dies cut a long rectangle. Since I don’t have the long rect. set yet, I played around until I figured out I could get my std. rect. to do the same thing. I’ll probably have to do it again and take pics cause it’s a little hard to explain. After I cut the long rect., I used the frame of the large one and sponged on green ink. I did the same to the small one and stamped the sentiment in the center.

    The dp looking stuff is actually wrapping paper. I die cut the letter and shadow then attached them to a nestie circle. I added two little ribbon tabs on the left side.

    I’ll try to explain how I made a long rectangle out of a standard nestie rectangle. Basically, take for example, the 1″ x 2″ nestie rectangle and make your card stock larger, say, 1 1/2″ X 4″. Place your nestie on the card stock near one end. It’s probably important to note that I use mine with the original Sizzix machine, so I don’t know what you’d have to do differently for other machines. Then place the die in the machine but not all the way. Leave the last 1/2″ or so (toward the center) uncut. Place on your mat and emboss. Carefully remove the nestie die and reposition toward the opposite end and repeat, again omitting the last 1/2″ toward the center. If done correctly, you will have a long, 1″ x approx 3 1/2″ rectangle. If you’ll check back tomorrow, I’ll try to have pics and a better description. Pics will make it so much easier to understand.

    UPDATE: Here’s the tutorial for this. Resizing Your Nesties

    Julie2 sig

    Supplies:
    Stamps: FireCracker Designs by Pamela
    Paper: vanilla, = to marigold morning, bravo burgundy, garden green, wrapping paper
    Ink: Ancient Page sienna, leaf green, bordeaux, Kaleidacolor Autumn Leaves & Desert Heat rainbow pads
    Accessories: foam tape, Sizzix shadow letter die, nestie rectangles & circles, cb harvest and just my type border folders, markers, brown gel pen, ribbon

     


  • Ombré Watercolor Resist

    Supplies Needed
    Supplies Needed
    Supplies:
    1. Watercolor paper
    2. ¾” Flat Wash Paint Brush
    3. Adirondack reinkers in Butterscotch, Ginger, Raisin and Eggplant (I keep drops of mine in these little round, divided craft containers-it’s fine when they dry out; just reactivate with a little water)
    4. Tiled Quad Cube stamp (Stampendous)
    5. Encore Ultimate Metallic Gold ink (Tsukineko)
    6. Clear Embossing Powder & Heat Tool
    7. Water

     

    (Click any picture to enlarge)

    Step 1
    Step 1 & 2

    Step 1:

    Stamp image repeatedly onto watercolor paper using the gold ink. Coat with clear powder and heat emboss.

    Step 2:

    Use the paint brush to wet the entire piece.

    Step 3:

    With the water loaded paint brush, pick up some of the Butterscotch ink and begin washing it across the wet background. Begin at the lower edge and work your way up. The ink will become lighter as you move up the page. When adding more ink, always begin at the lower edge.

    Step 2
    Step3

     

    Step 3 after application of Butterscotch ink
    Step 4
    Step 4

    Step 4:

    With the water loaded paint brush, pick up some of the Ginger ink and float in only on the bottom ½ of the piece

    Step 5
    Step 5

     

    Step 6
    Step 6

    Step 5 & 6:

    With the water loaded paint brush, pick up some of the Raisin ink and float in on the bottom 1/3 of the piece. Finally, float in a little Eggplant ink on the lower 1/3. I used Eggplant because I don’t have a darker brown reinker. Since the dk. purple Eggplant is the opposite (or complement on the color wheel) of the orangey yellows it will produce the brown color I need.

    (Optional)

    Let the piece dry for a few minutes, then load the paint brush with water and add a little Eggplant ink. Tap the paint brush against your other hand while holding it over the piece. This will produce a splatter pattern.

    Finished background
    Finished background

    Finished Piece:Comparasion: left was done with reinkers, right strip was done with traditional watercolor paints.

    Comparison- reinkers on left, tradional watercolors on right
    Comparison- note reinkers are slightly more transparent

     

    DTGD08Michele DTGD08Christine DTGD08Lauren Model T494a
    Finished card using the background

     

    Julie2 sig